Connectors
380V Plug
We often need 380V plugs in projects. We only use these Mennekes plugs, they are best quality available. And are built to last a very long time. Features: screwless, with insulating displacing technique, SafeCONTACT, cable gland and sealing, strain relief and protection against kinking, enclosure with thread lock and safety slide
| MennekesCEE Startop Typ:33 16A-6h 3P+N+gnd | € 9.99 (ex. vat)  |
| MennekesCEE Startop Typ:34 32A-6h 3P+N+gnd | € 14.99 (ex. vat) |
380V plug phase inverter
This is a special type of 380V plug. It has a built in feature which allows you to easily invert the phases. 2 phases are mounted on a swivel type of contact. All you need to do is unplug the device from power, then use a screw driver to rotate the swivel 180 degrees, and the phases are inverted...| Mennekes CEE phase inverter Typ:319 16A 3P+N+gnd | € 52.99 (ex. vat) |
| Mennekes CEE phase inverter Typ:322 32A 3P+N+gnd | € 61.99 (ex. vat) |
380V Coupler
We often need 380V Couplers in projects. We only use these Mennekes couplers, they are best quality available. And are built to last a very long time. Features: screwless, with insulating displacing technique, SafeCONTACT, cable gland and sealing, strain relief and protection against kinking, enclosure with thread lock and safety slide| MennekesCEE Startop Typ:35 16A-6h 3P+N+gnd | € 11.99 (ex. vat) |
| MennekesCEE Startop Typ:36 32A-6h 3P+N+gnd | € 16.99 (ex. vat) |
SUB-D Screw Terminals
We often use these connector to connect encoder cables. Although at first sight it seems to be an expensive connector, when you take into account that it is much easier to connect than a solder connection. And also much less fault prone, and easy to maintain. Also standard it has a metalised shell, and easy shielding connection, which makes it very well EMC prone...| 9 pole MALE | € 24.99 (ex. vat) |
| 9 pole FEMALE | € 24.99 (ex. vat) |
Neutrik Panelmount
We often use these connectors in our own projects.
It is a very rugged industrial connector. When using the correct contra connectors, it is perfectly EMC shielded.| USB | € 7.99 (ex. vat) |
| Ethernet | € 12.99 (ex. vat) |
| HDMI | € 13.99 (ex. vat) |
5 pole connector & bus +wiring
This is the type of connector we use in our RTR sets. Its a quality connector that has some nice features. No soldering is required since its a screw connector. The bus has been prewired with 40CM of wire. Its possible to fixate the connector to the bus with locking screws. We can offer these directly from our stock.| 5PoleConnector&PrewiredBus(NOT IN STOCK) | € 6.68 (ex. vat) |
5 Pole DIN Bus
5 pole, nickelplated,contacts silverplated,reliable contact. This bus accompanies DIN connector.| Price for each. | € 1.19 (ex. vat) |
5 Pole DIN connectors
5 pole, nickelplated, contacts silverplated, reliable contact.| Price for each. | € 1.55 (ex. vat) |
5 Pole DIN secured BUS
5 Pole DIN BUS secured. A high quality connector. Which is easier to solder than the 5 Pole DIN BUS. Further the connector can be secured with thread.| 5 Pole DIN secured BUS MALE | € 5.71 (ex. vat) |
5 Pole DIN secured connector
5 Pole DIN secured connector. A high quality connector. Which is easier to solder than the 5 Pole DIN Connector. Further it can be secured to the bus with thread. | 5 Pole DIN secured connector FEMALE | € 7.99 (ex. vat) |
Heavy Duty Circular Connectors
These connectors are for rough environment. We prefer these connectors because they are very robust. A big plus point is that for (3+PE) its a screw connector, which saves a lot of soldering time.| 3+PE Cable Female | € 6.49 (ex. vat) |
| 3+PE Cable Male | € 6.49 (ex. vat) |
| 3+PE Chassis Female | € 5.49 (ex. vat) |
| 3+PE Chassis Male | € 5.49 (ex. vat) |
IPS Cable Connector (ScrewType)
These connectors are compatibele with our plug and play sensor system that is used in the RTR sets. This connector is intended for those who which to connect other sensors than we supply, or to make custom cable lengths. The connectors are high quality screw type connectors, which makes the connection quite easy.| M12_Straight_Male | € 7.10 (ex. vat) |
| M12_Straight_Female | € 7.10 (ex. vat) |
| M12_90DegreeAngle_Male | € 7.10 (ex. vat) |
| M12_90DegreeAngle_Female | € 7.10 (ex. vat) |
Ribbon Cable
Ribbon Cable Connectors
10 Pole ribbon cable is used to connect the Steppermotor drivers to the USBCNC or Mach 3 interface.
26 Pole ribbon cable is used to make LPT poort connections for Mach 3 systems.| 10 Pole Ribbon Connector | € 0.38 (ex. vat) |
| 26 Pole Ribbon Connector | € 0.52 (ex. vat) |
Sub-D to Ribbon Cable connectors
| 10 PoleRibbon to 9 pole SUB-D connector MALE | € 1.42 (ex. vat) |
| 10 PoleRibbon to 9 pole SUB-D connector FEMALE | € 1.42 (ex. vat) |
| 26 PoleRibbon to 25 pole SUB-D connector MALE | € 2.99 (ex. vat) |
| 26 PoleRibbon to 25 pole SUB-D connector FEMALE | € 2.99 (ex. vat) |
SUB-D Connector
A standard SUB-D connector. Often used for making simple connections. We also have covers for the SUB-D connectors.| SUB-D Male 9Pole | € 0.99 (ex. vat) |
| SUB-D FeMale 9Pole | € 0.99 (ex. vat) |
| SUB-D Male 25Pole | € 1.59 (ex. vat) |
| SUB-D FeMale 25Pole | € 1.99 (ex. vat) |
Sub-D Covers
A cover that can be used in combination with Sub-D connectors. Please note, it will not work in combination with ribbon to SUB-D connectors.| 9 Pole | € 1.42 (ex. vat) |
| 25 Pole | € 1.42 (ex. vat) |
Sub-D Mount Screw Set
The Sub-D mounts on the back of your PC and those used in our controllers dont have metric but UNC thread. When building housings its important to use the correct UNC bolts otherwise the thread will be damaged. Here we offer a set of 2 bolts,nuts,rings, in the correct 4-40 UNC thread.| One Set | € 0.83 (ex. vat) |
Breaking news
2012-11-17
NEW PRODUCT Mini Mill Spiral Patterned
Tool designed for milling glas and epoxy based materials2012-10-11
NEW PRODUCT Closed Loop Stepper Systems
A lowcost alternative to a servo system2012-06-30
New Bulk Discount
New Bulk Discount feature added to DamenCNC website
We supply worldwide!
